Functions
uint16_t	wiced_bt_l2cap_allocate_psm (void)

wiced_bool_t	wiced_bt_l2cap_cancel_ble_connect_req (wiced_bt_device_address_t rem_bda)

uint16_t	wiced_bt_l2cap_connect_req (uint16_t psm, wiced_bt_device_address_t p_bd_addr, wiced_bt_l2cap_ertm_information_t *p_ertm_information)

uint8_t	wiced_bt_l2cap_data_write (uint16_t cid, uint8_t *p_buf, uint16_t buf_len, uint16_t flags)

void	wiced_bt_l2cap_deregister (uint16_t psm)

wiced_bool_t	wiced_bt_l2cap_disconnect_req (uint16_t cid)

wiced_bool_t	wiced_bt_l2cap_disconnect_rsp (uint16_t cid)

wiced_bool_t	wiced_bt_l2cap_enable_update_ble_conn_params (wiced_bt_device_address_t rem_bda, wiced_bool_t enable)

uint16_t	wiced_bt_l2cap_ertm_connect_req (uint16_t psm, wiced_bt_device_address_t p_bd_addr, wiced_bt_l2cap_ertm_information_t *p_ertm_information)

void	wiced_bt_l2cap_ertm_enable (void)

wiced_bool_t	wiced_bt_l2cap_flow_control (uint16_t cid, wiced_bool_t data_enabled)

uint16_t	wiced_bt_l2cap_flush_channel (uint16_t lcid, uint16_t num_to_flush)

wiced_bool_t	wiced_bt_l2cap_get_bdaddrby_handle (uint16_t handle, wiced_bt_device_address_t bd_addr)

uint8_t	wiced_bt_l2cap_get_ble_conn_role (wiced_bt_device_address_t bd_addr)

uint8_t	wiced_bt_l2cap_get_chnl_fcr_mode (uint16_t lcid)

wiced_bool_t	wiced_bt_l2cap_get_current_config (uint16_t lcid, wiced_bt_l2cap_cfg_information_t *pp_our_cfg, wiced_bt_l2cap_ch_cfg_bits_t p_our_cfg_bits, wiced_bt_l2cap_cfg_information_t *pp_peer_cfg, wiced_bt_l2cap_ch_cfg_bits_t p_peer_cfg_bits)

uint16_t	wiced_bt_l2cap_get_disconnect_reason (wiced_bt_device_address_t remote_bda, tBT_TRANSPORT transport)

wiced_bool_t	wiced_bt_l2cap_get_peer_features (wiced_bt_device_address_t bd_addr, uint32_t p_ext_feat, uint8_t p_chnl_mask)

uint16_t	wiced_bt_l2cap_le_connect_req (uint16_t le_psm, wiced_bt_device_address_t p_bd_addr, wiced_bt_ble_address_type_t bd_addr_type, wiced_bt_ble_conn_mode_t conn_mode, uint16_t rx_mtu, uint8_t rx_sdu_pool_id, uint8_t req_security, uint8_t req_encr_key_size)

wiced_bool_t	wiced_bt_l2cap_le_connect_rsp (wiced_bt_device_address_t p_bd_addr, uint8_t id, uint16_t lcid, uint16_t result, uint16_t rx_mtu, uint8_t rx_sdu_pool_id)

uint8_t	wiced_bt_l2cap_le_data_write (uint16_t cid, uint8_t *p_data, uint16_t buf_len, uint16_t flags)

wiced_bool_t	wiced_bt_l2cap_le_deregister (uint16_t le_psm)

uint16_t	wiced_bt_l2cap_le_determ_secur_rsp (wiced_bt_device_address_t bd_addr, uint8_t req_secur, uint8_t req_encr_key_size)

wiced_bool_t	wiced_bt_l2cap_le_disconnect_req (uint16_t lcid)

wiced_bool_t	wiced_bt_l2cap_le_disconnect_rsp (uint16_t lcid)

uint16_t	wiced_bt_l2cap_le_get_peer_mtu (uint16_t lcid)

uint16_t	wiced_bt_l2cap_le_register (uint16_t le_psm, wiced_bt_l2cap_le_appl_information_t p_cb_information, void context)

wiced_bool_t	wiced_bt_l2cap_le_set_user_congestion (uint16_t lcid, wiced_bool_t is_congested)

uint16_t	wiced_bt_l2cap_register (uint16_t psm, wiced_bt_l2cap_appl_information_t p_cb_information, void context)

wiced_bool_t	wiced_bt_l2cap_set_acl_priority (wiced_bt_device_address_t bd_addr, uint8_t priority)

wiced_bool_t	wiced_bt_l2cap_set_acl_priority_ext (wiced_bt_device_address_t bd_addr, uint8_t priority, uint8_t direction)

wiced_bool_t	wiced_bt_l2cap_set_chnl_flushability (uint16_t cid, wiced_bool_t is_flushable)

uint8_t	wiced_bt_l2cap_set_desire_role (uint8_t new_role)

wiced_bool_t	wiced_bt_l2cap_set_flush_timeout (wiced_bt_device_address_t bd_addr, uint16_t flush_timeout)

wiced_bool_t	wiced_bt_l2cap_set_idle_timeout (uint16_t cid, uint16_t timeout, wiced_bool_t is_global)

wiced_bool_t	wiced_bt_l2cap_set_idle_timeout_by_bd_addr (wiced_bt_device_address_t bd_addr, uint16_t timeout, tBT_TRANSPORT transport)

uint8_t	wiced_bt_l2cap_set_trace_level (uint8_t trace_level)

wiced_bool_t	wiced_bt_l2cap_set_tx_priority (uint16_t cid, wiced_bt_l2cap_chnl_priority_t priority)

wiced_bool_t	wiced_bt_l2cap_update_ble_conn_params (wiced_bt_device_address_t rem_bdRa, uint16_t min_int, uint16_t max_int, uint16_t latency, uint16_t timeout)

Detailed Description

API Functions module for L2CAP.

Function Documentation

◆ wiced_bt_l2cap_allocate_psm()

uint16_t wiced_bt_l2cap_allocate_psm ( void )

Function wiced_bt_l2cap_allocate_psm

            Other layers call this function to find an unused PSM for
            L2CAP services.

Returns: PSM to use.

◆ wiced_bt_l2cap_cancel_ble_connect_req()

wiced_bool_t wiced_bt_l2cap_cancel_ble_connect_req ( wiced_bt_device_address_t rem_bda )

Function wiced_bt_l2cap_cancel_ble_connect_req

            Cancel a pending connection attempt to a BLE device.

Parameters

[in] rem_bda BD Address of remote

Returns: : TRUE if connection was cancelled

◆ wiced_bt_l2cap_connect_req()

uint16_t wiced_bt_l2cap_connect_req	(	uint16_t	psm,
		wiced_bt_device_address_t	p_bd_addr,
		wiced_bt_l2cap_ertm_information_t *	p_ertm_information )

Function wiced_bt_l2cap_connect_req

            Higher layers call this function to create an L2CAP connection.
            Note that the connection is not established at this time, but
            connection establishment gets started. The callback function
            will be invoked when connection establishes or fails.

Parameters

[in]	psm	: PSM value
[in]	p_bd_addr	: BD Address
[in]	p_ertm_information	: ERTM info

Returns: the CID of the connection, or 0 if it failed to start

◆ wiced_bt_l2cap_data_write()

uint8_t wiced_bt_l2cap_data_write	(	uint16_t	cid,
		uint8_t *	p_buf,
		uint16_t	buf_len,
		uint16_t	flags )

Function wiced_bt_l2cap_data_write

            Higher layers call this function to write data with extended

Parameters

[in]	cid	TODO
[in]	p_data	TODO
[in]	flags	L2CAP_FLUSHABLE_CH_BASED L2CAP_FLUSHABLE_PACKET L2CAP_NON_FLUSHABLE_PACKET

Returns: L2CAP_DATAWRITE_SUCCESS, if data accepted, else FALSE L2CAP_DATAWRITE_CONGESTED, if data accepted and the channel is congested L2CAP_DATAWRITE_FAILED, if error

◆ wiced_bt_l2cap_deregister()

void wiced_bt_l2cap_deregister ( uint16_t psm )

Function wiced_bt_l2cap_deregister

            Other layers call this function to deregister for L2CAP
            services.

Parameters

[in] psm PSM value

Returns: void

◆ wiced_bt_l2cap_disconnect_req()

wiced_bool_t wiced_bt_l2cap_disconnect_req ( uint16_t cid )

Function wiced_bt_l2cap_disconnect_req

            Higher layers call this function to disconnect a channel.

Parameters

[in] cid CID value

Returns: TRUE if disconnect sent, else FALSE

◆ wiced_bt_l2cap_disconnect_rsp()

wiced_bool_t wiced_bt_l2cap_disconnect_rsp ( uint16_t cid )

Function wiced_bt_l2cap_disconnect_rsp

            Higher layers call this function to acknowledge the
            disconnection of a channel.

Parameters

[in] cid CID value

Returns: void

◆ wiced_bt_l2cap_enable_update_ble_conn_params()

wiced_bool_t wiced_bt_l2cap_enable_update_ble_conn_params	(	wiced_bt_device_address_t	rem_bda,
		wiced_bool_t	enable )

Function wiced_bt_l2cap_enable_update_ble_conn_params

            Update BLE connection parameters.

Parameters

[in]	rem_bda	Remote Bd Address
[in]	enable	Enable Flag

Returns: : TRUE if update started

◆ wiced_bt_l2cap_ertm_connect_req()

uint16_t wiced_bt_l2cap_ertm_connect_req	(	uint16_t	psm,
		wiced_bt_device_address_t	p_bd_addr,
		wiced_bt_l2cap_ertm_information_t *	p_ertm_information )

Function wiced_bt_l2cap_ertm_connect_req

            Higher layers call this function to create an L2CAP connection
            that needs to use Enhanced Retransmission Mode.
            Note that the connection is not established at this time, but
            connection establishment gets started. The callback function
            will be invoked when connection establishes or fails.

Parameters

[in]	psm	PSM value
[in]	p_bd_addr	BD Address
[in]	p_ertm_info	ERTM info

Returns: the CID of the connection, or 0 if it failed to start

◆ wiced_bt_l2cap_ertm_enable()

void wiced_bt_l2cap_ertm_enable ( void )

Function wiced_bt_l2cap_ertm_enable

Description Enable ERTM.

             Calling this function will cause the linker to include
             ERTM related functions.

Parameters

[in] void

Returns: void

◆ wiced_bt_l2cap_flow_control()

wiced_bool_t wiced_bt_l2cap_flow_control	(	uint16_t	cid,
		wiced_bool_t	data_enabled )

Function wiced_bt_l2cap_flow_control

            Higher layers call this function to flow control a channel.

            data_enabled - TRUE data flows, FALSE data is stopped

Parameters

[in]	cid	CID value
[in]	data_enabled	data enabled

Returns: TRUE if valid channel, else FALSE

◆ wiced_bt_l2cap_flush_channel()

uint16_t wiced_bt_l2cap_flush_channel	(	uint16_t	lcid,
		uint16_t	num_to_flush )

Function wiced_bt_l2cap_flush_channel

        This function flushes none, some or all buffers queued up
        for xmission for a particular CID. If called with
        L2CAP_FLUSH_CHANNELS_GET (0), it simply returns the number
        of buffers queued for that CID L2CAP_FLUSH_CHANNELS_ALL (0xffff)
        flushes all buffers.  All other values specifies the maximum
        buffers to flush.

Parameters

[in]	lcid	LCID value
[in]	num_to_flush	Number of items for flushing

Returns: Number of buffers left queued for that CID

◆ wiced_bt_l2cap_get_bdaddrby_handle()

wiced_bool_t wiced_bt_l2cap_get_bdaddrby_handle	(	uint16_t	handle,
		wiced_bt_device_address_t	bd_addr )

Function wiced_bt_l2cap_get_bdaddrby_handle

             Get BD address for the given HCI handle

Parameters

[in]	handle	HCI handle
[in]	bd_addr	Peer Bd Address

Returns: : TRUE if found lcb for the given handle, FALSE otherwise

◆ wiced_bt_l2cap_get_ble_conn_role()

uint8_t wiced_bt_l2cap_get_ble_conn_role ( wiced_bt_device_address_t bd_addr )

Function wiced_bt_l2cap_get_ble_conn_role

            This function returns the connection role.

Parameters

[in] bd_addr BD Address

Returns: link role.

◆ wiced_bt_l2cap_get_chnl_fcr_mode()

uint8_t wiced_bt_l2cap_get_chnl_fcr_mode ( uint16_t lcid )

Function wiced_bt_l2cap_get_chnl_fcr_mode

             Get the channel FCR mode

Parameters

[in] lcid Local CID

Returns: : Channel mode

◆ wiced_bt_l2cap_get_current_config()

wiced_bool_t wiced_bt_l2cap_get_current_config	(	uint16_t	lcid,
		wiced_bt_l2cap_cfg_information_t **	pp_our_cfg,
		wiced_bt_l2cap_ch_cfg_bits_t *	p_our_cfg_bits,
		wiced_bt_l2cap_cfg_information_t **	pp_peer_cfg,
		wiced_bt_l2cap_ch_cfg_bits_t *	p_peer_cfg_bits )

Function wiced_bt_l2cap_get_current_config

        This function returns configurations of L2CAP channel

Parameters

[in]	lcid	Local CID
[in]	pp_our_cfg	pointer of our saved configuration options
[in]	p_our_cfg_bits	valid config in bitmap
[in]	pp_peer_cfg	pointer of peer's saved configuration options
[in]	p_peer_cfg_bits	: valid config in bitmap

Returns: TRUE if successful

◆ wiced_bt_l2cap_get_disconnect_reason()

uint16_t wiced_bt_l2cap_get_disconnect_reason	(	wiced_bt_device_address_t	remote_bda,
		tBT_TRANSPORT	transport )

Function wiced_bt_l2cap_get_disconnect_reason

            This function returns the disconnect reason code.

Parameters

[in]	remote_bda	Remote BD Address
[in]	transport	Transport (BR-EDR or LE)

Returns: disconnect reason

◆ wiced_bt_l2cap_get_peer_features()

wiced_bool_t wiced_bt_l2cap_get_peer_features	(	wiced_bt_device_address_t	bd_addr,
		uint32_t *	p_ext_feat,
		uint8_t *	p_chnl_mask )

Function wiced_bt_l2cap_get_peer_features

             Get a peers features and fixed channel map

Parameters

[in]	bd_addr	Peer Bd Address
[in]	p_ext_feat	features
[in]	p_chnl_mask	mask storage area

Returns: : TRUE if peer is connected

◆ wiced_bt_l2cap_le_connect_req()

uint16_t wiced_bt_l2cap_le_connect_req	(	uint16_t	le_psm,
		wiced_bt_device_address_t	p_bd_addr,
		wiced_bt_ble_address_type_t	bd_addr_type,
		wiced_bt_ble_conn_mode_t	conn_mode,
		uint16_t	rx_mtu,
		uint8_t	rx_sdu_pool_id,
		uint8_t	req_security,
		uint8_t	req_encr_key_size )

Function wiced_bt_l2cap_le_connect_req

            Higher layers call this function to create an L2CAP connection
            for LE_PSM.
            Note that the connection is not established at this time, but
            connection establishment gets started. The callback function
            will be invoked when connection establishes or fails.

Parameters

[in]	le_psm	: LE PSM value
[in]	p_bd_addr	: BD Address
[in]	bd_addr_type	: BLE_ADDR_PUBLIC or BLE_ADDR_RANDOM
[in]	conn_mode	: BLE_CONN_MODE_HIGH_DUTY or BLE_CONN_MODE_LOW_DUTY
[in]	rx_mtu	: Rx MTU value (must be <= ACL_POOL_SIZE)
[in]	rx_sdu_pool_id	: Rx SDU pool ID (typically L2CAP_DEFAULT_BLE_CB_POOL_ID)
[in]	req_security	: Security required
[in]	req_encr_key_size	: key size

Returns: the CID of the connection, or 0 if it failed to start

◆ wiced_bt_l2cap_le_connect_rsp()

wiced_bool_t wiced_bt_l2cap_le_connect_rsp	(	wiced_bt_device_address_t	p_bd_addr,
		uint8_t	id,
		uint16_t	lcid,
		uint16_t	result,
		uint16_t	rx_mtu,
		uint8_t	rx_sdu_pool_id )

Function wiced_bt_l2cap_le_connect_rsp

            Higher layers call this function to accept an incoming
            LE L2CAP connection, for which they had gotten an connect
            indication callback.

Parameters

[in]	p_bd_addr	TODO
[in]	id	TODO
[in]	lcid	TODO
[in]	result	TODO
[in]	rx_mtu	TODO
[in]	rx_sdu_pool_id	TODO

Returns: TRUE for success, FALSE for failure

◆ wiced_bt_l2cap_le_data_write()

uint8_t wiced_bt_l2cap_le_data_write	(	uint16_t	cid,
		uint8_t *	p_data,
		uint16_t	buf_len,
		uint16_t	flags )

Function wiced_bt_l2cap_le_data_write

            Send data over LE connection-oriented channel.

Parameters

[in]	cid	Channel ID
[in]	p_data	Input buffer
[in]	buf_len	p_data buffer size

Returns: L2CAP_DATAWRITE_SUCCESS, if data accepted, else FALSE L2CAP_DATAWRITE_CONGESTED, if data accepted and the channel is congested L2CAP_DATAWRITE_FAILED, if error

◆ wiced_bt_l2cap_le_deregister()

wiced_bool_t wiced_bt_l2cap_le_deregister ( uint16_t le_psm )

Function wiced_bt_l2cap_le_deregister

            Other layers call this function to deregister L2CAP services
            for LE_PSM.

Parameters

[in] le_psm LE PSM value

Returns: void

◆ wiced_bt_l2cap_le_determ_secur_rsp()

uint16_t wiced_bt_l2cap_le_determ_secur_rsp	(	wiced_bt_device_address_t	bd_addr,
		uint8_t	req_secur,
		uint8_t	req_encr_key_size )

Function wiced_bt_l2cap_le_determ_secur_rsp

            Higher layers call this function to check if the current
            device security settings are sufficient to continue with
            call establishment.
            It is called by call acceptor on reception of LE Credit
            Based Connection Request.

Parameters

[in]	bd_addr	BD Address
[in]	req_secur	Security required
[in]	req_encr_key_size	Key size

Returns: L2CAP_CONN_OK/L2CAP_BLE_CONN_BAD_AUTHENT/ L2CAP_BLE_CONN_BAD_KEY_SIZE/L2CAP_BLE_CONN_BAD_ENCRYPT/ L2CAP_CONN_NO_RESOURCES.

◆ wiced_bt_l2cap_le_disconnect_req()

wiced_bool_t wiced_bt_l2cap_le_disconnect_req ( uint16_t lcid )

Function wiced_bt_l2cap_le_disconnect_req

            Higher layers call this function to disconnect a LE COC
            channel.

Parameters

[in] lcid LCID value

Returns: TRUE if disconnect sent, else FALSE

◆ wiced_bt_l2cap_le_disconnect_rsp()

wiced_bool_t wiced_bt_l2cap_le_disconnect_rsp ( uint16_t lcid )

Function wiced_bt_l2cap_le_disconnect_rsp

            Higher layers call this function to acknowledge the
            disconnection of a LE COC channel.

Parameters

[in] lcid TODO

Returns: void

◆ wiced_bt_l2cap_le_get_peer_mtu()

uint16_t wiced_bt_l2cap_le_get_peer_mtu ( uint16_t lcid )

Function wiced_bt_l2cap_le_get_peer_mtu

            Higher layers call this function to get peer MTU.

Parameters

[in] lcid LCID value

Returns: Peer MTU or 0.

◆ wiced_bt_l2cap_le_register()

uint16_t wiced_bt_l2cap_le_register	(	uint16_t	le_psm,
		wiced_bt_l2cap_le_appl_information_t *	p_cb_information,
		void *	context )

Function wiced_bt_l2cap_le_register

            Other layers call this function to register L2CAP services
            for LE_PSM.

Parameters

[in]	le_psm	LE PSM value
[in]	p_cb_info	L2CAP cb info
[in]	context	Caller context to return in callbacks

Returns: LE_PSM to use or zero if error. Typically the LE_PSM returned is the same as was passed in, but for an outgoing-only connection a "virtual" LE_PSM is returned and should be used in the calls to wiced_bt_l2cap_le_connect_req() and wiced_bt_l2cap_le_deregister().

◆ wiced_bt_l2cap_le_set_user_congestion()

wiced_bool_t wiced_bt_l2cap_le_set_user_congestion	(	uint16_t	lcid,
		wiced_bool_t	is_congested )

Function wiced_bt_l2cap_le_set_user_congestion

            Higher layers call this function to tell if the connection
            is congested or not

Parameters

[in]	lcid	LCID value
[in]	is_congested	TRUE, if congested

Returns: TRUE if command processed OK

◆ wiced_bt_l2cap_register()

uint16_t wiced_bt_l2cap_register	(	uint16_t	psm,
		wiced_bt_l2cap_appl_information_t *	p_cb_information,
		void *	context )

Function wiced_bt_l2cap_register

            Other layers call this function to register for L2CAP
            services.

Parameters

[in]	psm	PSM value
[in]	p_cb_info	L2CAP cb info
[in]	context	Caller context to return in callbacks

Returns: PSM to use or zero if error. Typically, the PSM returned is the same as was passed in, but for an outgoing-only connection to a dynamic PSM, a "virtual" PSM is returned and should be used in the calls to wiced_bt_l2cap_connect_req() and BTM_SetSecurityLevel().

◆ wiced_bt_l2cap_set_acl_priority()

wiced_bool_t wiced_bt_l2cap_set_acl_priority	(	wiced_bt_device_address_t	bd_addr,
		uint8_t	priority )

Function wiced_bt_l2cap_set_acl_priority

            Sets the priority for an ACL channel

Parameters

[in]	bd_addr	BD Address
[in]	priority	[L2CAP_PRIORITY_NORMAL \| L2CAP_PRIORITY_HIGH]

Returns: TRUE if a valid channel, else FALSE

◆ wiced_bt_l2cap_set_acl_priority_ext()

wiced_bool_t wiced_bt_l2cap_set_acl_priority_ext	(	wiced_bt_device_address_t	bd_addr,
		uint8_t	priority,
		uint8_t	direction )

Function wiced_bt_l2cap_set_acl_priority_ext

            Sets the priority for an ACL channel
            with extended parameters.

Parameters

[in]	bd_addr	BD Address
[in]	priority	[L2CAP_PRIORITY_NORMAL \| L2CAP_PRIORITY_HIGH]
[in]	direction	[L2CAP_DIRECTION_DATA_SOURCE \| L2CAP_DIRECTION_DATA_SINK]

Returns: TRUE if a valid channel, else FALSE

◆ wiced_bt_l2cap_set_chnl_flushability()

wiced_bool_t wiced_bt_l2cap_set_chnl_flushability	(	uint16_t	cid,
		wiced_bool_t	is_flushable )

Function wiced_bt_l2cap_set_chnl_flushability

            Higher layers call this function to set a channels
            flushability flags

Parameters

[in]	cid	CID value
[in]	is_flushable	TRUE, if flushable

Returns: TRUE if CID found, else FALSE

◆ wiced_bt_l2cap_set_desire_role()

uint8_t wiced_bt_l2cap_set_desire_role ( uint8_t new_role )

Function wiced_bt_l2cap_set_desire_role

        This function sets the desire role for L2CAP.
        If the new role is L2CAP_ROLE_ALLOW_SWITCH, allow switch on
        HciCreateConnection.
        If the new role is L2CAP_ROLE_DISALLOW_SWITCH, do not allow switch on
        HciCreateConnection.

        If the new role is a valid role (HCI_ROLE_MASTER or HCI_ROLE_SLAVE),
        the desire role is set to the new value. Otherwise, it is not changed.

Parameters

[in] new_role New role value

Returns: the new (current) role

◆ wiced_bt_l2cap_set_flush_timeout()

wiced_bool_t wiced_bt_l2cap_set_flush_timeout	(	wiced_bt_device_address_t	bd_addr,
		uint16_t	flush_timeout )

Function wiced_bt_l2cap_set_flush_timeout

            This function set the automatic flush time out in Baseband
            for ACL-U packets.

Parameters

[in]	bd_addr	The remote BD address of ACL link. If it is BT_DB_ANY then the flush time out will be applied to all ACL link.
[in]	flush_timeout	flush time out in ms 0x0000 : No automatic flush L2CAP_NO_RETRANSMISSION : No retransmission 0x0002 - 0xFFFE : flush time out, if (flush_timeout*8)+3/5) <= HCI_MAX_AUTO_FLUSH_TOUT (in 625us slot). Otherwise, return FALSE. L2CAP_NO_AUTOMATIC_FLUSH : No automatic flush

Returns: TRUE if command succeeded, FALSE if failed

NOTE This flush timeout applies to all logical channels active on the ACL link.

◆ wiced_bt_l2cap_set_idle_timeout()

wiced_bool_t wiced_bt_l2cap_set_idle_timeout	(	uint16_t	cid,
		uint16_t	timeout,
		wiced_bool_t	is_global )

Function wiced_bt_l2cap_set_idle_timeout

            Higher layers call this function to set the idle timeout for
            a connection, or for all future connections. The "idle timeout"
            is the amount of time that a connection can remain up with
            no L2CAP channels on it. A timeout of zero means that the
            connection will be torn down immediately when the last channel
            is removed. A timeout of 0xFFFF means no timeout. Values are
            in seconds.

Parameters

[in]	cid	CID value
[in]	timeout	Timeout value
[in]	is_global	TRUE, if global

Returns: TRUE if command succeeded, FALSE if failed

◆ wiced_bt_l2cap_set_idle_timeout_by_bd_addr()

wiced_bool_t wiced_bt_l2cap_set_idle_timeout_by_bd_addr	(	wiced_bt_device_address_t	bd_addr,
		uint16_t	timeout,
		tBT_TRANSPORT	transport )

Function wiced_bt_l2cap_set_idle_timeout_by_bd_addr

            Higher layers call this function to set the idle timeout for
            a connection. The "idle timeout" is the amount of time that
            a connection can remain up with no L2CAP channels on it.
            A timeout of zero means that the connection will be torn
            down immediately when the last channel is removed.
            A timeout of 0xFFFF means no timeout. Values are in seconds.
            A bd_addr is the remote BD address. If bd_addr = BT_BD_ANY,
            then the idle timeouts for all active l2cap links will be
            changed.

Parameters

[in]	bd_addr	BD Address
[in]	timeout	Timeout value

Returns: TRUE if command succeeded, FALSE if failed

NOTE This timeout applies to all logical channels active on the ACL link.

◆ wiced_bt_l2cap_set_trace_level()

uint8_t wiced_bt_l2cap_set_trace_level ( uint8_t trace_level )

Function wiced_bt_l2cap_set_trace_level

            This function sets the trace level for L2CAP. If called with
            a value of 0xFF, it simply reads the current trace level.

Parameters

[in] trace_level Trace level

Returns: the new (current) trace level

◆ wiced_bt_l2cap_set_tx_priority()

wiced_bool_t wiced_bt_l2cap_set_tx_priority	(	uint16_t	cid,
		wiced_bt_l2cap_chnl_priority_t	priority )

Function wiced_bt_l2cap_set_tx_priority

            Sets the transmission priority for a channel. (FCR Mode)

Parameters

[in]	cid	CID
[in]	priority	[L2CAP_PRIORITY_NORMAL \| L2CAP_PRIORITY_HIGH]

Returns: TRUE if a valid channel, else FALSE

◆ wiced_bt_l2cap_update_ble_conn_params()

wiced_bool_t wiced_bt_l2cap_update_ble_conn_params	(	wiced_bt_device_address_t	rem_bdRa,
		uint16_t	min_int,
		uint16_t	max_int,
		uint16_t	latency,
		uint16_t	timeout )

Function wiced_bt_l2cap_update_ble_conn_params

            Update BLE connection parameters.

Parameters

[in]	rem_bdRa	Remote BD Address
[in]	min_int	Min interval
[in]	max_int	Max interval
[in]	latency	Latency value
[in]	timeout	Timeout value

Returns: : TRUE if update started